S Series

The Constructive Series S 4 “, are multicellular submerged centrifugal electric well pumps for domestic, industrial, irrigation and pressurized water installations by means of hydraulic accumulators.

They are designed for the extraction of water from deep wells and reduced drilling diameter.
Its modular composition is formed by the hydraulic pump, and the submersible electric motor, which is coupled to the bottom of the pump.
They can work vertically or horizontally (with cooling bell).
The pump is supported by normal trade pipe sections that expel the water to the outside.
Power ratings range from 0.5 to 10 hp in three-phase to 220, 380, 400, 415 volts and from 0.5 to 3 hp in single-phase.
Pumps cannot run dry.
Maximum liquid temperature 30º.
Maximum sand 200 gr/m3.
Built-in check valve.

Some of its advantages are :

It is not necessary to dismantle the strainer to pass the cable.
High corrosion resistance of the entire pump.
Good hydraulic performance, higher yields
Its configuration allows to increase/decrease the pressure, adding or eliminating phases.
Eliminates priming complications, pump always in charge (submerged)
Eliminates problems in aspiration
Avoids air intakes
No pump-motor alignment problems
Less noise pollution
Cost reduction, minimum maintenance.
No need for a bench, reduced installation space
Less civil works
Longer service life

Characteristics	Image	Materials
The installations of the series consist of three parts 1- Hydraulic body The hydraulic body is made up of a suction body, a discharge body, and stages or phases, made up of closed multi-channel radial type diffuser and impeller bodies. The different stages are cased in a stainless steel casing that guarantees a high resistance to the whole pump and avoids possible deformations. The diameter of the group is 4″. The set of impellers driven by the central shaft that transmits the power of the motor. 2- Submersible electric motor Electric submersible motor of 50 or 60 Hz with IP-68 protection that supports the axial thrust of the pump, by means of a widely dimensioned axial bearing. The stator winding is flooded in oil or water, the bearings are lubricated by the internal liquid, and require no maintenance. These engines are manufactured by the most prestigious specialized firms. The coupling flanges are designed in accordance with NEMA standards, simplifying maintenance and repair operations. 3- Hydraulic column The hydraulic column is made up of sections or stages of normal commercial piping, depending on the depth of the well.		HYDRAULIC BODY
		Suction body	Stainless steel
		Drive body	Stainless steel
		Diffuser body	Noryl
		Rodete	Noryl
		Pump shaft	Stainless steel
		Outer Shell	Stainless steel
		Optional:	Can be supplied with speed variator “Variache” and “Varivip”, according to power and voltage
		ENGINES
		Submersibles motors IP68 in water or oil bath	Optional AISI 316

2. SD Series

Its modular composition is formed by the hydraulic pump, and the submersible electric motor, which is coupled to the bottom of the pump.
They can work vertically or horizontally (with cooling bell).
The pump is supported by the tubes of columna´, which expel the water to the outside.
Custom fabrication for every application and installation.
Maximum liquid temperature 25º.
Maximum sand 40 gr/m3

Some of its advantages are :

Good hydraulic performance, higher yields
Its configuration allows to increase/decrease the pressure, adding or eliminating phases.
Eliminates priming complications, pump always in charge (submerged)
Eliminates problems in aspiration
Avoids air intakes
No pump-motor alignment problems
Less noise pollution
Cost reduction, minimum maintenance.
No need for a bench, reduced installation space
Less civil works
Longer service life

Characteristics

Image

Materials

The installations of the series consist of three parts:

1- Hydraulic body

The hydraulic body is made up of a suction body, a discharge body, and stages or phases, made up of diffuser bodies and closed multi-channel impellers of the semi-axial type.
The diameter of the group can be 6-8-10-12-14 and 16 inches, it varies according to the perforation and the service data.
The operating pressure can be obtained by incorporating the necessary number of stages thanks to its modular configuration.
The set of impellers driven by the central shaft that transmits the power of the motor.

2- Submersible electric motor

Electric submersible motor of 50 or 60 Hz with IP-68 protection that supports the axial thrust of the pump, by means of a widely dimensioned axial bearing.
The stator winding is flooded in oil or water, depending on whether it is 6-8-10 and 12″, in all cases the bearings are lubricated by the internal liquid, and do not need maintenance.
These engines are manufactured by the most prestigious specialized firms.
The coupling flanges are designed in accordance with NEMA standards, simplifying maintenance and repair operations.

3- Hydraulic column

The hydraulic column is made up of sections, depending on the depth of the well. These sections consist of tubes with steel flanges.

1- Hydraulic Body

Suction body: GG25 – (Optional bronze, superduplex, AISI, steel)
Drive body: GG25 – (Optional bronze; superduplex; AISI; steel)
Diffuser body: GG25 – (Optional bronze, superduplex, AISI, steel)
Rodete: GG25 – (Optional bronze, superduplex, AISI, steel)
Pump shaft: AISI 420 (Optional AISI 316)
Bushing: AISI 1045 – (Optional AISI 316)
Casting: stainless steel

2- Hydraulic Column

3- Motor

IP68 submersible motors in water or oil bath. (Optional AISI 316)

3. SDX Series

The SDX series are multicellular submerged centrifugal electric well pumps. All AISI 316 stainless steel with optimized design and thickness for water extraction from deep wells and reduced drilling diameter.

Its modular composition is formed by the hydraulic pump, and the submersible electric motor, which is coupled to the bottom of the pump.
They can work vertically or horizontally (with cooling bell).
The pump is supported by the tubes of columna´, which expel the water to the outside.
Custom fabrication for every application and installation.
Maximum liquid temperature 25º.
Maximum sand 160 gr/m3

Some of its advantages are :

Good hydraulic performance, higher yields
Its configuration allows to increase/decrease the pressure, adding or eliminating phases.
Eliminates priming complications, pump always in charge (submerged)
Eliminates problems in aspiration
Avoids air intakes
No pump-motor alignment problems
Less noise pollution
Cost reduction, minimum maintenance.
No need for a bench, reduced installation space
Less civil works
Longer service life

Characteristics

Image

Materials

1- Hydraulic body totally in AISI 316

The hydraulic body AISI 316 is made up of a suction body, a discharge body, and stages or phases, made up of diffuser bodies and closed multi-channel impellers of the semi-axial type.
The diameter of the group can be 6-8 and 10 inches, it varies according to the perforation and the service data.
The operating pressure can be obtained by incorporating the necessary number of stages thanks to its modular configuration.
The set of impellers driven by the central shaft that transmits the power of the motor.

2- Submersible electric motor

Electric submersible motor of 50 or 60 Hz with IP-68 protection that supports the axial thrust of the pump, by means of a widely dimensioned axial bearing.
The stator winding is flooded in oil or water, depending on whether it is 4-6-8-10 and 12″, in all cases the bearings are lubricated by the internal liquid, and do not need maintenance.
These engines are manufactured by the most prestigious specialized firms.
The coupling flanges are designed in accordance with NEMA standards, simplifying maintenance and repair operations.

3- Hydraulic column

The hydraulic column is made up of sections, depending on the depth of the well. These sections consist of tubes with steel flanges.

HYDRAULIC BODY

Aspiration body	AISI 316 (Optional AISI 304)
Drive body	AISI 316 (Optional AISI 304)
Diffuser body	AISI 316 (Optional AISI 304)
Rodete	AISI 316 (Optional AISI 304)
Pump shaft	AISI 316 (Optional AISI 304)
Buje	AISI 316
Striner	AISI 316

ENGINES

Submersible motors in water or oil bath

Optional AISI 316

4. ST - STI Series

Its modular composition is formed by the hydraulic pump, and the submersible electric motor, which is coupled to the bottom of the pump.
They can work vertically or horizontally (with cooling bell).
The pump is supported by the tubes of columna´, which expel the water to the outside.
Custom fabrication for every application and installation.
Maximum liquid temperature 25º.
Maximum sand 40 gr/m3

Some of its advantages are :

Good hydraulic performance, higher yields
Its configuration allows to increase/decrease the pressure, adding or eliminating phases.
Eliminates priming complications, pump always in charge (submerged)
Eliminates problems in aspiration
Avoids air intakes
No pump-motor alignment problems
Less noise pollution
Cost reduction, minimum maintenance.
No need for a bench, reduced installation space
Less civil works
Longer service life

Characteristics

Image

Materials

The installations of the series consist of three parts:

1- Hydraulic body

The hydraulic body is made up of a suction body, a discharge body, and stages or phases, made up of closed multi-channel axial type diffuser and impeller bodies.
The different stages are cased in a stainless steel casing that guarantees a high resistance to the whole pump and avoids possible deformations.
The diameter of the group is 6″.
The set of impellers driven by the central shaft that transmits the power of the motor.

2- Submersible electric motor

Electric submersible motor of 50 or 60 Hz with IP-68 protection that supports the axial thrust of the pump, by means of a widely dimensioned axial bearing.
The stator winding is flooded in oil or water, the bearings are lubricated by the internal liquid, and require no maintenance.
These engines are manufactured by the most prestigious specialized firms.
The coupling flanges are designed in accordance with NEMA standards, simplifying maintenance and repair operations.

3- Hydraulic column

The hydraulic column is made up of sections, depending on the depth of the well. These sections can be formed by normal commercial piping or by steel flanged piping.

HYDRAULIC BODY

Aspiration body	GG-25
Drive body	GG-25
Diffuser body	NORYL
Rodete	NORYL
Pump shaft	STAINLESS STEEL
Outer sell	STAINLESS STEEL

ENGINES

Submersible motors IP68 in water or oil bath

Optional AISI 316

5. Triton Series

Submersible electric pumps for wells, multicellular 4″ and 6″.

Characteristics

Image

Materials

Radial type pump.
Maximum liquid temperature of 30ºC.
Counterclockwise rotation direction.
Built-in check valve.
Different models SJI, SKI, SLI, SMI, SPI, SQI, STI, ST.
It is not necessary to dismantle the strainer to pass the cable.
High corrosion resistance throughout the pump.
Stainless steel impulsion body.
Stainless steel suction body with built-in strainer.

Radial or semi-axial turbines.
Diffusers in Norly.
Ceramic-rubber bearings.
Motors with oil bath.
Stainless steel outer casing and shaft.
Check valve built into the discharge body.
Pump-to-motor coupling according to NEMA standard.
On request, it can be supplied with VARIACHE or VARIVIP speed depending on power and voltage.